Why did my Yamaha receiver die after power outage?

Whilst there was no power (still plugged in), I tried switching it on (with the remote) and it ‘weakly’ came on with the usual click which was weird, but it ‘died’ after that. I tried turning it on after the power came back, and it now does not turn on full stop, no light, no click no nothing.

What to do when your Yamaha radio shuts off?

Turn the receiver on, and turn the volume control up to about half way. If the receiver stays on, please go to Step 3. If the receiver shuts off right away, the unit will require service. Please consult with your dealer for further assistance.

Why does my Yamaha unit shut off at 1 / 4 volume or less?

Yamaha receivers have a built in computerized protection circuit, which will activate in certain over-current conditions. This means that the unit is drawing too much current through the amplifier or power supply, and the built in computer turns the receiver off.

Why did my Yamaha receiver go into thermal protection mode?

Here is a possible explanation. When you operated the receiver during a period of very low voltage you caused the receiver to draw more current that it could handle, causing overheating. The receiver may have gone into a thermal protection mode and been inoperable until it cooled down.

What kind of stereo receiver does a Yamaha have?

Vintage Yamaha CR-820 AM/FM Natural Sound Stereo Receiver, Tested! Needs Lamps 3 product ratings – Vintage Yamaha CR-820 AM/FM Natural Sound Stereo Receiver, Tested! Needs Lamps Vintage Yamaha R-1000 Receiver Great working condition See pictures.

Why did my Yamaha rx-v471 receiver die?

Yamaha RX-V471 died on me and sorry to tell you, it wasn’t a power surge. And even if it would have been one, my whole system is plugged in a APC Back UPS 1300W and it is still going on strong. So my AV was working in the best conditions.

How do you turn off a Yamaha receiver?

Push the power button, MAIN appear and then turn off. The Service manual talk about updating Firmware but I never found any RXV471-xxxx.bin file anywhere on the internet. Hold TONE CONTROL + INFO + POWER Buttons. Scroll all Main and Sub-Menus. Everything is ok.

Whilst there was no power (still plugged in), I tried switching it on (with the remote) and it ‘weakly’ came on with the usual click which was weird, but it ‘died’ after that. I tried turning it on after the power came back, and it now does not turn on full stop, no light, no click no nothing.

Yamaha RX-V471 died on me and sorry to tell you, it wasn’t a power surge. And even if it would have been one, my whole system is plugged in a APC Back UPS 1300W and it is still going on strong. So my AV was working in the best conditions.

What kind of sound does a Yamaha aventage have?

Yamaha AVENTAGE RX-A780 7.2-ch 4K Ultra HD AV Receiver with HDR, Dolby Vision, Dolby Atmos, Wi-Fi, Phono, YPAO and MusicCast. Works with Alexa. This 7.2-channel (5.2.2-channel) AVENTAGE AV receiver features Dolby Atmos and DTS:X, Zone 2, dual HDMI outputs and YPAO – Reflected Sound Control auto-calibration

Push the power button, MAIN appear and then turn off. The Service manual talk about updating Firmware but I never found any RXV471-xxxx.bin file anywhere on the internet. Hold TONE CONTROL + INFO + POWER Buttons. Scroll all Main and Sub-Menus. Everything is ok.

How to post about a Yamaha outboard problem?

UPLOAD AN IMAGE OF YOUR PROBLEM EQUIPMENT! Give us a detailed description, short 5 word posts are not much use and will not be posted. Put your boat info, outboard make and model or basic detail in the post title. More useful information at fishing and boats. Have a Yamaha outboard problem to share?

How to reset the decoder off warning on a Yamaha?

Then plug in the cable box and the receiver. Turn on and let it reboot. Then power on the Yamaha. This in most cases resets the Decoder OFF warning on Yamaha units. If you need further assistance, let me know. Still no sound. Same error message. Yes, not very clear. Yes, the manual advised to do that as well. Still no sound. I’m stumped.

Here is a possible explanation. When you operated the receiver during a period of very low voltage you caused the receiver to draw more current that it could handle, causing overheating. The receiver may have gone into a thermal protection mode and been inoperable until it cooled down.