How do I reset my Z906?
How do I reset my Z906?
To reset your Z906 to the factory default settings:
- Power your Z906 off using the Power button on the Control Console.
- While in the “Off” state, press and hold down the Input button for eight (8) seconds. You’ll see several lights on the Control Console light up and there will be a popping sound from the speakers.
How do I test my Logitech surround sound speakers?
To test whether you have correctly set up your speakers, press and hold the INPUT button on the remote control or control console for 5 seconds to put your system into test mode. In test mode, the system cycles through each speaker, playing an audible test signal.
How do I pair my Z906?
To use an analog connection with your Z906 speakers, connect your DVD or Blueray player to Input 2 on the back of your subwoofer and select Input 2 on the Control Console. NOTE: If either or both the DVD/Blueray player and the media you’re playing aren’t in a surround sound format, the Z906 can simulate surround sound.
How do I fix my Logitech Z906 sound?
Sounds like you either have the wrong settings in Windows audio or you don’t have the speakers hooked up properly to the motherboard. Check over the audio settings make sure it’s set to 5.1 and that the speakers are wired to the correct ports for 5.1 audio on the sound card.
How do I know if my headset is surround sound?
Generally any headphone will give a good left and right stereo image, but headphones with a good soundstage will give a smooth pan across your ears with no gaps, and you should be able to tell if the sound is in front of you or behind you fairly reliably.
Can a z906 speakers connect to a computer?
There are a few different ways you can connect your Z906 speakers to your computer. The method you choose will depend on your computer’s output options. NOTE: Not all computer sound cards support surround sound audio. Refer to your computer’s documentation to determine whether your sound card is capable of surround sound audio output.
What kind of cable does the Logitech z906 surround sound system use?
Connecting your speaker cables The Z906 comes with five speaker cables: two 7.6-meter cables for the rear satellites and three 4.6-meter cables for the front and center satellites. When connecting your speakers, the control console, and your audio source, make sure the power to the system is off.
Why are the rear speakers on my Logitech z506 not working?
When I do a sound test set up in 5.1 configuration the rear right and left speakers don’t work. The rear speakers work when I select 7.1 settings and click the sound test button but then when I play music and media that I know is in surround sound format the rear speakers are extremely quite and almost no sound comes out
Can a z906 decode Dolby Digital sound?
If the Z906 receives neither DTS Digital Sound nor Dolby Digital decoding data, the Z906 will not be able to decode the signal. You can resolve this issue by making sure the Z906 receives only a DTS Digital Sound or Dolby Digital signal from the host device (for example, DVD/Blu-ray player, game console, or home computer).
How is my z906 speaker system connected to my TV?
I have my Z906 speaker system connected to my TV (Panasonic Viera TX-50CX700B) via optical digital cable. I didn’t realise until recently but I don’t think the speakers are outputting correct 5.1 sound. I think it is getting stereo sound and then converting this to 2.1.
Connecting your speaker cables The Z906 comes with five speaker cables: two 7.6-meter cables for the rear satellites and three 4.6-meter cables for the front and center satellites. When connecting your speakers, the control console, and your audio source, make sure the power to the system is off.
When I do a sound test set up in 5.1 configuration the rear right and left speakers don’t work. The rear speakers work when I select 7.1 settings and click the sound test button but then when I play music and media that I know is in surround sound format the rear speakers are extremely quite and almost no sound comes out
How do I connect my z906 to my computer?
For 6-channel analog (6-channel direct): Match the color-coded 3.5mm outputs on the back of your sound card to the corresponding inputs on the back of your Z906 Control Console using the provided cable. Press the Input button on the front of your Z906 Control Console.
