How do I reset my wireless subwoofer?

Press and hold PAIRING on the back of the wireless subwoofer for more than 5 seconds, until the led on the subwoofer blinks red and green alternating. Unplug the power cord of the soundbar and the wireless subwoofer. Connect them again after the LED of the main unit and the wireless subwoofer are fully turned off.

Why is my JBL subwoofer not working?

If you run into a pairing issues it is important to unplug everything from the main unit (all HMDI and other connections except for power) and reset the bar by pressing and holding three buttons (volume up and down and source) until the device shows that is has reset. Unplug the power cable and unplug the subwoofer.

Why is my Samsung wireless subwoofer not working?

Check your wall outlet. Unplug the subwoofer and plug it back in. It should have a standby light if it’s receiving power. If it’s not, test the outlet with something else, like a lamp. If the outlet has no power, the issue is with the outlet (although hopefully it’s something simple, like a tripped circuit).

How do wireless subwoofers get power?

The home theater receiver, through a wireless transmitter, sends the low-frequency impulses to the wireless subwoofer. The subwoofer’s built-in amplifier produces the power required to allow you to hear the sound.

How can you tell if subwoofer is blown?

Physical Inspection Pressing on the subwoofer can indicate whether it’s blown. A functioning subwoofer has suspension that allows for movement. Use both hands and gently press on either side of the subwoofer’s speaker cone. If the cone is rigid or locked in place, the subwoofer is definitely blown.

How do I reset my JBL wireless subwoofer?

Press and hold 5 seconds SOUND button to reset default audio setting.

How to troubleshoot no sound coming from an Active Subwoofer?

A separate article about the difference between an active subwoofer and a passive subwoofer is available. Select Settings. Select Speaker. Select Speaker SP. Make sure that the Speaker pattern ends in either a .1 or .2. NOTE: If a pattern that ends in .0 is selected, the subwoofer will not work.

What to do if your subwoofer is not pairing up?

How can I tell if my Sony subwoofer is still on?

In this case, set the sound field setting to A.F.D. AUTO or a another sound field. Sony® receivers will send a simulated LFE signal to the subwoofer and the SW indicator will light up. Verify the subwoofer power cord is plugged into an active AC outlet and that the subwoofer is powered on.

Why is my subwoofer not working on my TV?

NOTE: If a pattern that ends in .0 is selected, the subwoofer will not work. Verify that the subwoofer indicator light on the front panel of the A/V receiver is on. Depending on the audio source, the low frequency effect (LFE) signal may not be sent to your subwoofer.

How to fix no sound from subwoofer speaker?

Check the volume setting for the subwoofer output in the receiver too. Have you turned on the subwoofer output in the receiver speaker set up menu? Check the volume setting for the subwoofer output in the receiver too. Click to expand… Contact PSB. They may have a reasonably priced option to either repair or replace the crossover/amp in the sub.

Why do I not get thumping sound from my subwoofer?

If you do not hear a thumping sound then there is a possible service issue with the subwoofer. Connect the other end of the subwoofer cable to the subwoofer audio output connector on the back of the receiver. NOTE: Some receiver models may have two outputs to drive two subwoofers.

Are there any problems with a wireless subwoofer?

One of the most glaring problems with subwoofers is the common ‘ground loop issue’ or hum. Ground loop can be eliminated in large part by using a wireless sub because the sub is not technically hard wired to the rest of the system.

How can I tell if my subwoofer is turned on?

Verify that the subwoofer is turned on. On the remote control, press the SW + (subwoofer volume) button to turn up the volume of the subwoofer. Check the status of the subwoofer LED indicator. When the LED lights up in red after turning on the audio device, the link or the connection between the unit and the subwoofer may not be complete.